Supports

 

Anchor Plate (AP)

Used to support the grease duct or conduit in vertical runs. It is attached to the floor by means of anchors (not included). It is designed to be supported on four (4) sides. Structural angles may be used to support sides that are unsupported.

Includes: 1- Assembly Band (AB)
  1- Finishing Band (FB)

K=Same as pipe length

I.D. A
in mm in mm
6 152 22.000 559
8 203 24.000 610
10 254 26.000 660
12 305 28.000 711
14 356 30.000 762
16 406 32.000 813
18 457 34.000 864
20 508 36.000 914
22 559 38.000 965
24 610 40.000 1016
26 660 42.000 1067
28 711 44.000 1118
30 762 46.000 1168
32 813 48.000 1219
34 864 50.000 1270
36 914 52.000 1321
38 965 54.000 1372
40 1016 56.000 1422
42 1067 58.000 1473
44 1118 60.000 1524
46 1168 62.000 1575
48 1219 64.000 1626

Roof Support (RS)

Used to support and guide the portion of the grease duct or conduit which extends to the roof. It is attached to the roof curb by means of four (4) angles. It keeps a minimum distance between the grease duct or conduit and combustible materials at the roof.

I.D. O.D. A
in mm in mm in mm
6" to 14" 152 to 356 10" to 18" 254 to 457 5.250 133
16" to 22" 406 to 559 20" to 26" 508 to 660 7.250 184
24" to 32" 610 to 813 30" to 36" 711 to 914 9.250 235
34" to 42" 965 to 1067 38" to 46" 965 to 1168 11.250 286
44" to 48" 1118 to 1219 48" to 52" 1219 to 1321 13.250 337

Hanger Bracket (HB)

Used to support the horizontal runs of grease duct or conduit. To be installed by means of 3/8”Ø (19mm) threaded rods (not included). Generally installed every 5’-0” (1525mm).

Wall Support (WS)

Used to support the grease duct or conduit in vertical runs. It keeps the grease duct or conduit at an adjustable distance between 4” (102mm) and 10” (254mm) from the wall. The oblique braces may be attached to the wall either above or below the supporting surface.

Includes: 1 - Assembly Band (AB)
  1 - Finishing Band (FB)
  2 - Adjustable Angles
  2 - Braces
  4 - Wall Brackets

K = Same as pipe length

I.D. A
in mm in mm
6 152 14.000 356
8 203 16.000 406
10 254 18.000 457
12 305 20.000 508
14 356 22.000 559
16 406 24.000 610
18 457 26.000 660
20 508 28.000 711
22 559 30.000 762
24 610 32.000 813
26 660 34.000 864
28 711 36.000 914
30 762 38.000 965
32 813 40.000 1016
34 864 42.000 1067
36 914 44.000 1118
38 965 46.000 1168
40 1016 48.000 1219
42 1067 50.000 1270
44 1118 52.000 1321
46 1168 54.000 1372
48 1219 56.000 1422

Horizontal Support (HS)

Used to support the grease duct or conduit in horizontal runs. It keeps the grease duct or conduit at an adjustable distance from the ceiling. The oblique braces (not included) may be attached to the ceiling either ahead of or behind the supporting surface.

Includes: 1- Assembly Band (AB)
  1- Finishing Band (FB)
  4- Wall Brackets

K=Same as pipe length

I.D.  A
in mm in mm
6 152 14.000 356
8 203 16.000 406
10 254 18.000 457
12 305 20.000 508
14 356 22.000 559
16 406 24.000 610
18 457 26.000 660
20 508 28.000 711
22 559 30.000 762
24 610 32.000 813
26 660 34.000 864
28 711 36.000 914
30 762 38.000 965
32 813 40.000 1016
34 864 42.000 1067
36 914 44.000 1118
38 965 46.000 1168
40 1016 48.000 1219
42 1067 50.000 1270
44 1118 52.000 1321
46 1168 54.000 1372
48 1219 56.000 1422